Chester Clinic

 

Evva.ie

Bedienungsanleitung User Guide Guide d'utilisation Istruzione d'uso Manual de uso Bedieningshandleiding Elektronischer Zylinder Electronic cylinder Cylindre électronique
Cilindro elettronico Cilindro electrónico Elektronische cilinder
Technische Änderungen/Abweichungen und Druckfehler vorbehalten. Das Copyright liegt bei der EVVA Sicherheitstechnologie GmbH. Technical changing and misprint are subject to change. Copyright by EVVA Sicherheitstechnologie GmbH. Sous réserve de modifications/divergences techniques et d‘erreurs d‘impression. Tous droits réservés à EVVA Sicherheitstechnologie GmbH. Con riserva di modifiche tecniche/differenze ed errori di stampa. Il copyright è di EVVA Sicherheitstechnologie GmbH. Sujeto a modificaciones/divergencias técnicas y errores de impresión. Copyright de EVVA Sicherheitstechnologie GmbH. Technische wijzigingen/afwijkingen en drukfouten voorbehouden. Copyright berust bij EVVA Sicherheitstechnologie GmbH.
Electronic cylinder The e-primo cylinder in detail
– EN 1634-1 fire protection Thumb turn cover/inside thumb turn 2 Battery in battery compartment Outside thumb turn (conical): – Diverse certifications with various lock manufacturers – e-primo iButton: Ø max. 35 mm, length 31 mm per EN 179 and EN 1125 (optional) – e-primo air: Ø max. 35 mm, length 32.5 mm 4 Inside locating screw Inside thumb turn (conical): Ø max. 40 mm, length 56 mm Power supply
1 × standard lithium battery, Panasonic CR 123A
6 Outside thumb turn Up to 90 %, non-condensing 8 Outside thumb turn Inside thumb turn: –20° C to +60° C Outside thumb turn: –20° C to +60° C 12 Outside locating screw 13 Cam 14 INIT button The components
Included in cylinder-package A
Available options C
– e-primo cylinder – cylinder fixing screw, M5x70 – cylinder fixing screw, M5x80 – special Allen wrench, ZTOOL1 – office key OK (Office Key) – lithium battery, CR123A – blocking key BK (Blocking Key) – cylinder fixing screw, M5x60 – emergency opening key EK (Emergency Key) – emergency power device (incl. 3-pole cable XRP0PC01 and 3 batteries, type AAA) Included in media-kit B
– programming key PK (Programming Key)
– 3 × user key UK (User Key)
– copy key CK (Copy Key)
– 4 × delete key DK (Delete Key)
Electronic cylinder An e-primo cylinder with a completely discharged battery can only be operated with the emergency power device 1 Loosen (turn clockwise) the inside thumb turn‘s fixing
Use only the specified, CR123A, battery type and be sure and a valid user key (see "Emergency power supply/Emer- screw with the special ZTOOL1 Allen wrench until there is of correct polarity when inserting a battery. Batteries gency opening"). Please contact your dealer if you do not contain chemical substances. They should therefore be have an emergency power device.
disposed of properly.
2 Pull off the thumb turn cover.
Weak battery
Notice: Please note, when the inside thumb turn cover
If the battery is weak, the e-primo cylinder will sound a is removed the outside thumb turn can operate the
descending warning tone and blink in orange twice before cam even without electronic authorisation. Avoid con-
it can be activated.
tamination of the e-primo cylinder when the thumb
turn cover is removed.
Replace the battery without delay when the "weak battery" condition is indicated. Repeated disregard of the 3 Open the battery clip and remove the discharged battery
"weak battery" warning can lead to inoperability of the from the battery compartment. Insert the new battery and e-primo cylinder.
close the battery clip so that it latches.
After the first "weak battery" warning only a maximum of 4 Carefully push the thumb turn cover onto the e-primo
2000 opening cycles are possible over the next 4 weeks cylinder. The inside locating screw must be engaged in (tested for Panasonic CR123A at room temperature). the cover‘s guide groove. Secure the screw carefully (turn counter-clockwise) with the special ZTOOL1 Allen wrench. Electronic cylinder Installing the e-primo cylinder
1 Loosen (turn clockwise) the outside thumb turn‘s fixing
5 Carefully push the outside thumb turn cover to its limit
screw with the special ZTOOL1 Allen wrench and pull it off.
onto the e-primo cylinder. The outer locating screw must Please note that it may not be possible to open the door be engaged in the guide groove. Fasten the outside thumb again after it is closed because the outside thumb turn will 2 Rotate the outside thumb turn such that the outer loca-
turn by carefully screwing in (turn counter-clockwise) its rotate passively, i.e. without engaging. After installation – ting screw is in the area of the cylinder profile.
screw with the special ZTOOL1 Allen wrench.
but before closing the door – insert a battery (see "Battery 3 Push the e-primo cylinder by hand, from inside to out-
insertion/replacement"), program the e-primo cylinder and Important: Please assign a programming key and a
side, through the escutcheon and the mortise lock (loosen test its functionality. The e-primo cylinder can now only be user key to the cylinder and make sure a functional
the escutcheon‘s fastening screws if necessary).
opened with a valid identification medium.
battery is inserted before closing the door!
4 Fasten the e-primo cylinder in the mortise lock with the
Should problems arise during installation, please contact cylinder fixing screw. The cylinder fixing screw should be your dealer or visit our website on the Internet at tightened down to a torque of 2 Nm (now also re-tighten the escutcheon‘s fastening screws if necessary). Place the gasket into the groove.
Notice: The specified IP rating is only achieved when
the gasket is in place.
Electronic cylinder Technology & media
User key UK (User Key) Blocking key BK (Blocking Key) (available option) The user key serves to lock and unlock the door, it is issued The blocking key sets the e-primo cylinder into a continu- The e-primo cylinder is available in versions for iButton or to the user. The user key can also be trained for additional ous locked condition; it cannot be activated from outside. air technology. User keys are therefore designed differently, functions, e.g. the office function.
This function can only be terminated by the programming depending on the technology.
Delete key DK (Delete Key) key or the emergency opening key. A single blocking key At least one programming key and one user key are can be assigned to multiple e-primo cylinders but only one The delete key is used in programming mode to delete required to operate one or more e-primo cylinders.
blocking key per e-primo cylinder is possible.
validation of a lost programming or user key from the e-primo cylinder‘s memory. Emergency opening key EK (Emergency Key) Programming key PK (Programming Key) (available option) Copy key CK (Copy Key) The programming key is used to start and stop the The emergency opening key sets the e-primo cylinder to The copy key is used in programming mode to start the programming procedure on the e-primo cylinder. It is also its emergency opening function (continuously open). This copy process in which the data of a programming or user used to limit the INIT button‘s function to the owner of function can only be terminated by the programming key key is stored onto a delete key.
the programming key as well as to terminate the blocking or the blocking key. A single emergency opening key can and emergency opening functions. A single programming Office key OK (Office Key) (available option) be assigned to multiple e-primo cylinders but only one key can be used for multiple e-primo cylinders.
The office key is used to train the user keys to the office emergency opening key per e-primo cylinder is possible. function as well as to enable the office function globally on an e-primo cylinder. The office function permits con-tinuous release of the e-primo cylinder (e.g. during office hours).
Assignment of user keys; programming mode Commissioning the e-primo cylinder
1 First hold the programming key briefly at the reader.
Ü A sequence of low and high tones will be emitted, the
The e-primo cylinder is not programmed to media when light ring blinks orange then green. The e-primo cylinder is now in its programming mode for 7 seconds.
2 Hold the user key you want to train into the e-primo
Assigning the programming key cylinder briefly at the reader within 7 seconds.
l Hold the programming key briefly at the reader.
Ü An ascending sequence of tones will be emitted, the Ü A sequence of high-pitch tones will be emitted, the light light ring illuminates orange then green. The e-primo ring blinks green. The e-primo cylinder now recognises cylinder now recognises this user key as valid for locking this medium as its programming key.
and unlocking the e-primo cylinder.
Notice: Please note that it may not be possible to
You can also assign several user keys, one after the other, open the door again after it is closed because the
by holding each of them at the reader within 7 seconds.
outside thumb turn will rotate passively, i.e. without
engaging. The e-primo cylinder can only be operated
3 Terminate programming mode by holding the program-
after assignment of a programming key and a user
ming key briefly at the reader or waiting for programming mode to terminate automatically.
Ü A descending sequence of tones will be emitted, the light ring illuminates orange then red.
Electronic cylinder Creating delete keys
Please note that delete keys can only be assigned
Deleting a user key which is on-hand 1 Start programming mode.
once to a programming or user key.
1 Start programming mode.
2 Hold the copy key briefly at the reader.
2 Hold the user key to be deleted (or multiple keys) briefly
Ü The light ring will blink orange.
Deleting a lost user key at the reader.
1 Start programming mode.
Ü A descending sequence of tones will be emitted, the 3 Hold the programming or user key, for which a delete
light ring illuminates orange then red. The user key is key is to be created, briefly at the reader within 5 seconds.
2 Hold the delete key for the lost user key briefly at the
deleted from the cylinder‘s memory.
Ü A high-pitched tone will be emitted, the light ring briefly illuminates green.
Ü A descending sequence of tones will be emitted, the 3 Terminate programming mode.
light ring illuminates orange then red. The lost user key 4 Hold the delete key briefly at the reader within 5 seconds.
Deleting a lost programming key, is deleted from the cylinder‘s memory.
Ü A high-pitched tone will be emitted, the light ring will assigning a new programming key illuminate green. The delete key for the programming or 3 Terminate programming mode.
1 Start programming mode by holding the delete key for
user key is now created.
the lost programming key at the reader.
If the delete key is held at the reader during normal ope- You can create multiple delete keys, one after the other, ration, the e-primo cylinder will indicate whether the lost 2 Hold the new programming key briefly at the reader
by repeating steps 3 and 4.
user key is still valid (green) or not (red). within 5 seconds.
Ü An ascending sequence of tones will be emitted, the 5 Terminate programming mode.
light ring illuminates orange then green. The new pro- Notice: You should mark all delete keys appropri-
gramming key is now assigned and the old programming ately for their corresponding keys so that when a
key is deleted from the memory.
delete key is needed the correct card is available for
If no new programming key is held at the reader within deleting. Delete keys should be safeguarded securely
5 seconds, the original programming key remains stored in and separately from programming and user keys.
the cylinder‘s memory.
1 Loosen (turn clockwise) the inside thumb turn‘s fixing
Limiting the INIT button‘s function screw with the special ZTOOL1 Allen wrench and pull off To avoid misuse, the functionality of the INIT button can 3 Terminate programming mode.
the outside thumb turn.
be limited to the owner of the programming key.
Even after assigning a new programming key, all user keys 2 Press the INIT button.
l Hold the programming key for about 5 seconds at the previously assigned to this e-primo cylinder retain their Ü During the deletion process a sequence of tones will be emitted and the light ring will illuminate alternately in Ü A sequence of ascending tones will be emitted, the light Resetting to factory settings
red, orange and green.
ring blinks green. The e-primo cylinder can now only be You can reset the e-primo cylinder to its factory settings so reset to factory settings if the programming key is being Ü A higher pitched tone will be emitted, the light ring will that all settings made, like assignments of media, blocking, held at the reader.
illuminate orange. The e-primo cylinder‘s memory is now office and emergency opening functions, are deleted from in its delivered state.
You can remove this limitation by holding the program- the cylinder‘s memory.
ming key at the reader again for 5 seconds.
3 Fasten the inside thumb turn by carefully screwing
in (counter-clockwise) its fixing screw with the special
Notice: Be sure that a delete key has been created
ZTOOL1 Allen wrench.
for the programming key. Otherwise, if the pro-
gramming key is lost, the e-primo cylinder must be
Notice: Please note that any person who has access
returned to EVVA for restoration.
to the ZTOOL1 Allen wrench is able to reset the
e-primo cylinder back to its factory settings.
Be aware, after resetting to factory settings, media
must again be assigned to the e-primi cylinder
before you close the door.
Electronic cylinder Supplementary functions (optional)
Training user keys to the office function Office function via user key 1 Start programming mode.
l Hold the entitled user key at the reader for at least 3 se- The following functions are available through the purchase conds, when the outside thumb turn is disengaged.
of an appropriate medium.
2 Hold the office key briefly at the reader.
Ü A sequence of ascending tones will be emitted, the light 3 Hold the user key at the reader within 5 seconds.
ring blinks green. The e-primo cylinder will be unlocked The e-primo cylinder can be switched to continuous open Ü An ascending sequence of tones will be emitted, the and is now in continuous open mode.
operation, e.g. for office hours.
light ring illuminates orange then green. The user key is You can deactivate continuous open mode by repeating Global disable/enable of the office function now entitled to use the office function.
this process.
Continuous open operation functionality can be globally 4 Terminate programming mode.
If the office function is globally disabled, continuous open disabled or enabled for the e-primo cylinder. It is enabled You can train multiple user keys to the office function, mode cannot be activated with a user key.
by factory setting.
one after the other, by repeating step 3.
1 Start programming mode.
You can revoke office function entitlement for a user key 2 Hold the office key for at least 3 seconds at the reader.
by repeating this process.
Ü A higher pitched tone will be emitted, the light ring will This process also simultaneously assigns any user key to illuminate green.
the cylinder if it was not already assigned previously – Ü After 3 seconds a descending tone will be emitted, the therefore the step "Assignment of user keys" can be light ring blinks red. The e-primo cylinder‘s continuous open mode is now disabled.
You can globally enable the office function again by repeating this process.
Emergency opening function
The e-primo cylinder can be continuously blocked with a The e-primo cylinder can be permanently opened with an blocking key, e.g. to lock up in case of a criminal act. User emergency opening key, e.g. in the event of fire. User keys keys are inoperable when blocking mode is set.
are inoperable when emergency opening mode is set.
A single blocking key can be assigned to multiple e-primo A single emergency opening key can be assigned to mul- cylinders, but only one blocking key per e-primo cylinder tiple e-primo cylinders but, only one emergency opening is possible.
key per e-primo cylinder is possible.
Notice: The blocking key must be assigned in the
Notice: The emergency opening key must be assi-
same manner as a user key before it is functional
gned in the same manner as a user key before it is
(see "Assignment of user keys").
functional (see "Assignment of user keys").
Activating the blocking function Activating the emergency opening function l Hold the assigned blocking key at the reader.
l Hold the assigned emergency opening key at the reader.
Ü A descending sequence of tones will be emitted, the Ü A sequence of ascending tones will be emitted, the light ring illuminates red. The blocking function is light ring illuminates green. Emergency opening mode Deactivating the blocking function Deactivating the emergency opening function l Hold the programming key at the reader.
l Hold the programming key at the reader.
Notice: An assigned emergency opening key can
Notice: An assigned blocking key can directly switch
directly switch the e-primo cylinder from blocking
the e-primo cylinder from emergency opening mode
mode into emergency opening mode.
into blocking mode.
Electronic cylinder Emergency power supply (optional)
Care of the e-primo cylinder
Use a soft, lint-free cloth and soapy water for cleaning. To ensure proper functionality of the e-primo cylinder, Never use products or sprays which can be aggressive to 1 Be sure batteries are inserted in the emergency power
EVVA recommends it be used in combination with a morti- metal surfaces. Pay attention, particularly when a turn‘s device – pay attention to correct polarity.
se lock in good operating condition.
cover is removed, that no liquid gets into the e-primo 2 Plug the 3-pole cable XRP0PC01 into the emergency power
Use of the e-primo cylinder in emergency exit doors or pa- device, then carefully plug it into the outside thumb turn.
nic doors conforming to EN 179 or EN 1125 is dependent on approval by the lock‘s manufacturer.
3 Slide the switch to "ON" to turn on the emergency
All media are to be continuously safeguarded such that power device.
Please use only the special ZTOOL1 Allen wrench to install they are only accessible to authorised persons. Delete keys the e-primo cylinder. should be safeguarded separately from programming and 4 To open the door, activate the e-primo cylinder with a
valid medium as usual.
EVVA‘s guarantee does not cover product defects caused by repairs, modifications or unprofessional servicing carried When a medium is lost, it should be deleted from the Notice: After this emergency opening process, please
out by unauthorised persons. Intervention in the electrical cylinder‘s memory without delay (see "Deleting media").
replace the e-primo cylinder‘s battery without delay.
or mechanical elements of the e-primo cylinder by unaut-horised persons also voids the guarantee.
What to do when .
The thumb turn may not be turned with pliers.
. the outside thumb turn is loose? Opening may not be affected with tools or other contri- – tighten the fixing screw with ZTOOL1 . the e-primo cylinder does not open? The e-primo cylinder also has plastic parts which could – replace discharged battery be broken by rough handling (e.g. hammering) during – perform emergency opening with the emergency power device – clean the reader The cylinder‘s thumb turn is not intended as an object to – send it to EVVA move the door leaf (as would be the door‘s knob, push-bar, handle, etc).
If you need help, please contact your dealer or visit our website on the Internet at www.evva.com/e-primo When the outside thumb turn is engaged, the inside thumb turn may not be held in place to prevent the locking/unlocking process.
Avoid contamination when the thumb turn cover is remo-ved, particularly by contact with greases, acids, moisture or external voltage sources.
Do not try to open the door by applying an external vol-tage source to the outside thumb turn.
The thumb turns may not be used as a means to step up.
Programming Key PK

Source: http://www.evva.ie/fileadmin/files_all/Download/Gebrauchsanleitung/Bedienungsanleitung_e-primo-Zylinder_EP_engl.pdf